Precision Metal Working (Associate's Degree) at Northcentral Technical College

Est. Earnings (1yr)

$41,504

Est. from national median (56 programs)

Est. Median Debt

$11,562

Est. from national median (20 programs)

Analysis

Wisconsin's precision metal working programs typically deliver strong earnings outcomes, with the state median at $52,449—well above the national figure. Northcentral Technical College's estimated first-year earnings of $41,504, derived from national peer programs, fall short of this state benchmark by more than $10,000. By year four, graduates here reach $45,379, which still trails the stronger showing at Fox Valley Technical College. This gap matters when considering career trajectory in a field where Wisconsin manufacturers typically pay premium wages.

The financial picture looks manageable on its own terms. Based on comparable associate programs at this institution, students typically finish with around $11,500 in debt—a modest burden relative to first-year earnings. That 0.28 debt-to-earnings ratio means graduates could theoretically pay off loans within three months of gross income, assuming disciplined repayment. For a two-year technical program, this represents reasonable risk.

The question is whether Northcentral delivers the same value as other Wisconsin precision metal working programs. If the earnings estimates hold true, graduates here would start $11,000 behind their peers at Fox Valley while facing similar debt loads. Parents should directly ask the school about job placement rates and whether their graduates match the higher state earnings standard, or if location and employer relationships explain the apparent gap.

Where Northcentral Technical College Stands

Earnings vs. debt across all precision metal working associates's programs nationally

Earnings Over Time

How earnings evolve from 1 year to 4 years after graduation

School	1 Year	4 Years	Growth
Northcentral Technical College	—	$45,379	—
Ferris State University	$56,811	$77,380	+36%
Hennepin Technical College	$59,829	$73,136	+22%
Ivy Tech Community College	$56,292	$64,893	+15%
Fox Valley Technical College	$52,449	$49,366	-6%

Compare to Similar Programs in Wisconsin

Precision Metal Working associates's programs at peer institutions in Wisconsin (7 total in state)

Scroll to see more →

School	In-State Tuition	Earnings (1yr)*	Earnings (4yr)	Median Debt*	Debt/Earnings
Northcentral Technical CollegeWausau	$3,861	$41,504*	$45,379	$11,562*	—
Fox Valley Technical CollegeAppleton	$4,916	$52,449*	$49,366	—*	—
National Median	—	$41,504*	—	$12,000*	0.29

* Estimated from similar programs

Career Paths

Occupations commonly associated with precision metal working graduates

Sheet Metal Workers

Fabricate, assemble, install, and repair sheet metal products and equipment, such as ducts, control boxes, drainpipes, and furnace casings. Work may involve any of the following: setting up and operating fabricating machines to cut, bend, and straighten sheet metal; shaping metal over anvils, blocks, or forms using hammer; operating soldering and welding equipment to join sheet metal parts; or inspecting, assembling, and smoothing seams and joints of burred surfaces. Includes sheet metal duct installers who install prefabricated sheet metal ducts used for heating, air conditioning, or other purposes.

$60,850/yrJobs growth:High school diploma or equivalent

Machinists

Set up and operate a variety of machine tools to produce precision parts and instruments out of metal. Includes precision instrument makers who fabricate, modify, or repair mechanical instruments. May also fabricate and modify parts to make or repair machine tools or maintain industrial machines, applying knowledge of mechanics, mathematics, metal properties, layout, and machining procedures.

$57,700/yrJobs growth:

Tool and Die Makers

Analyze specifications, lay out metal stock, set up and operate machine tools, and fit and assemble parts to make and repair dies, cutting tools, jigs, fixtures, gauges, and machinists' hand tools.

$57,700/yrJobs growth:

Welders, Cutters, Solderers, and Brazers

Use hand-welding, flame-cutting, hand-soldering, or brazing equipment to weld or join metal components or to fill holes, indentations, or seams of fabricated metal products.

$51,000/yrJobs growth:High school diploma or equivalent

Extruding and Drawing Machine Setters, Operators, and Tenders, Metal and Plastic

Set up, operate, or tend machines to extrude or draw thermoplastic or metal materials into tubes, rods, hoses, wire, bars, or structural shapes.

$46,800/yrJobs growth:

Forging Machine Setters, Operators, and Tenders, Metal and Plastic

Set up, operate, or tend forging machines to taper, shape, or form metal or plastic parts.

$46,800/yrJobs growth:

Rolling Machine Setters, Operators, and Tenders, Metal and Plastic

Set up, operate, or tend machines to roll steel or plastic forming bends, beads, knurls, rolls, or plate, or to flatten, temper, or reduce gauge of material.

$46,800/yrJobs growth:

Cutting, Punching, and Press Machine Setters, Operators, and Tenders, Metal and Plastic

Set up, operate, or tend machines to saw, cut, shear, slit, punch, crimp, notch, bend, or straighten metal or plastic material.

$46,800/yrJobs growth:

Drilling and Boring Machine Tool Setters, Operators, and Tenders, Metal and Plastic

Set up, operate, or tend drilling machines to drill, bore, ream, mill, or countersink metal or plastic work pieces.

$46,800/yrJobs growth:

Grinding, Lapping, Polishing, and Buffing Machine Tool Setters, Operators, and Tenders, Metal and Plastic

Set up, operate, or tend grinding and related tools that remove excess material or burrs from surfaces, sharpen edges or corners, or buff, hone, or polish metal or plastic work pieces.

$46,800/yrJobs growth:

Lathe and Turning Machine Tool Setters, Operators, and Tenders, Metal and Plastic

Set up, operate, or tend lathe and turning machines to turn, bore, thread, form, or face metal or plastic materials, such as wire, rod, or bar stock.

$46,800/yrJobs growth:

Milling and Planing Machine Setters, Operators, and Tenders, Metal and Plastic

Set up, operate, or tend milling or planing machines to mill, plane, shape, groove, or profile metal or plastic work pieces.

$46,800/yrJobs growth:

About This Data

Source: U.S. Department of Education College Scorecard (October 2025 release)

Population: Graduates who received federal financial aid (Title IV grants or loans). At Northcentral Technical College, approximately 17% of students receive Pell grants. Students who did not receive federal aid are not included in these figures.

Earnings: Median earnings from IRS W-2 data for graduates who are employed and not enrolled in further education, measured 1 year after completion. Earnings are pre-tax and include wages, salaries, and self-employment income.

Debt: Median cumulative federal loan debt at graduation. Does not include private loans or Parent PLUS loans borrowed on behalf of students.

Estimated Earnings: Actual earnings data is not available for this program (typically due to privacy thresholds when fewer than 30 graduates reported earnings). The estimate shown is based on the national median of 56 similar programs. Actual outcomes may vary.